A++10,000lbs Car Lift L1100 2 Post Lift Car Auto Truck Hoist FREE SHIPPING! 220V

• Popularity - 87728 views, 12532.6 views per day, 7 days on eBay. Super high amount of views. 390 sold.
• Price - Avg: $0.00, Low: $0.00, High: $0.00. Best quality when compared to PicClick similar items.
• Seller - + items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

Welcome to check our store for more items!<br>Welcome to our warehouses in CA to pick up yourself which will also save your money<br>10,000lbs Car Lift  L1100  2 Post Lift Car 220V<br>Warranty:<br>12 months warranty on all metal parts, pneumatic parts, electrical parts and motors! When you choose us, you will get the BEST warranty on eBay.<br>Most of the sellers don't provide or only provide warranty for those parts for 3 or 6 months, 1 year at most. Please compare with others before you make the decision. Get into our shop and you will see the details of terms and conditions, especially the best warranty!<br>Factory Defective Items:<br>Refunds issued for defective items will be for the full purchase price of the item.<br>If a replacement is requested, there will be no additional cost for shipping the replacement if your item is found to be defective<br>Auto Car L<br>ift  L 1100<br>Features:   220V  60HZ  1PH   3HP MOTOR<br>Auto Car Lift  L 1100<br>Features   220V  60HZ  1PH   3HP MOTOR<br>•<br>Symmetrical Arm Assembly:<br>Straight Front / Rear 2 Stage reach from 30 1/4" to 49 1/5"<br>Equal length of front and rear arm design<br>Drop-in type lifting pads and truck adapters included<br>Safety Mechanism:<br>Double Point Safety Lock Release<br>•Automatic arm lock restraints<br>•Relief valve built in power pump to prevent overloading<br>•Door guards protection rubber<br>•Up-limit switch to protect cylinders working stroke used in safe length scope<br>•Heavy duty 5/16" diameter cable and 4.56" pulley reduce high stress on synchronization process and increase cable life<br>•Stiffened base plate 5/8" thickness<br>•Ultra high molecular self lubricating nylon slider ensures carriage smooth moving up and down<br>•Anchor bolts/mounting hardware included<br>Control System<br>•Lifting operation by pressing "UP" button on motor<br>•Manual lowering operation by pressing lever<br>•Relief valve built in power pump to prevent overloading<br>•1 sets truck adapters included<br>•Lifting Capacity: 10,000 lbs<br>•The overall Height  145-5/8"<br>•The overall Width  133-1/4"<br>•Column Width    10.62"<br>•Base Width   18.89"<br>•Column Thickness of Steel    3/16"<br>•Carriage Thickness of Steel   15/64"<br>•Arms Thickness of Steel     15/64"<br>•Front Arm    30.7" to 48"<br>•Rear Arm<br>30.7" to 48"<br>•Min pad height: 3-7/8"<br>•Lift height max: 74.8"<br>•Drive-thru width clearance: 100"<br>•Time to full rise: 20-60 sec<br>•Shipping Weight: 1460 lbs<br>Site Selection<br>Before installing your auto lift, check the following:<br>• Lift Location: Always use architect’s plans when available.  Check layout dimension against floor plan requirements making sure adequate space is available.  Your lift<br>requires a 220v, 30amp, single phase, grounded electrical source.  There should be room enough to operate the lift in a safe manner and without restrictions.<br>• Overhead Area: The area where the lift will be located should be free of overhead obstructions such as heaters, building supports, electrical lines, doors, lights, etc.<br>• Floor Area: Visually inspect the site where the lift is to be installed and check for cracked or defective concrete.<br>Floor Requirements<br>• A level floor is suggested for proper installation and level lifting.  Small differences in floor slopes may be compensated for by proper shimming.  If a floor is of questionable slope, consider a survey of the site and/or the possibility of pouring a new level concrete slab.<br>• New concrete must be adequately cured for at least 30 days.<br>DO NOT install auto lift on any asphalt surface or any surface other than concrete.<br>DO NOT install auto lift on expansion seams or on cracked or defective concrete.<br>DO NOT install auto lift on a second/elevated floor without first consulting building architect.<br>DO NOT install auto lift outdoors unless special consideration has been made to protect the power unit from incleme